Nibe Heatpump Binding

The Nibe Heatpump binding is used to get live data from from Nibe heat pumps without using expensive MODBUS40 adapter. This binding should be compatible at least the F750, F1145 and F1245 heat pump models.

The binding support data telegrams (contains max 20 registers) from the heat pump, but binding can also read other registers from the pump. It's recommend to add most changed variables to telegram, binding will then read all other registers automatically from the pump when channels are linked to item. Register reading need to be enabled from the thing configuration. Binding have also experimental support for register writing. This can be used to configure heat pump. Write mode need to enabled from thing configuration and for safety reason all register identifiers need to explicitly defined.

Supported Things

This binding supports direct serial port connection (RS-485 adapter needed) to heat pump but also UDP connection via NibeGW software.

Thing type Description
f1x45-serial Serial port connected F1145 and F1245 Heat Pumps
f1x45-udp UDP connected Nibe F1145 and F1245 Heat Pumps
f1x45-simulator Simulator for Nibe F1145 and F1245 Heat Pumps
f750-serial Serial port connected F750 Heat Pumps
f750-udp UDP connected Nibe F750 Heat Pumps
f750-simulator Simulator for Nibe F750 Heat Pumps

Discovery

Discovery is not supported, therefore binding and things need to be configured via Paper UI or thing files.

Prerequisites

When Modbus adapter support is enabled from the heat pump UI, the heat pump will start to send telegrams every now and then. A telegram contains a maximum of 20 registers. Those 20 registers can be configured via the Nibe ModbusManager application.

Unfortunately Nibe has made this tricky: telegram from heat pump should be acknowledged, otherwise heat pump will raise an alarm and go in alarm state. Acknowledge (ACK or NAK) should be sent accurately. Binding support also direct serial port connections to heat pump, but heat pump will raise an alarm when openHAB binding not running e.g. during openHAB updates. This problem can be resolved by using the nibegw program, which can be run on Unix/Linux (such as a Raspberry Pi) or Arduino-based boards. If you are running openHAB on Raspberry Pi nibegw program can run also on the same machine, then when openHAB is not running nibegw will still acknowledge packets to heat pump. Obviously, this doesn't solve the problem when whole Raspberry Pi is down, therefore Arduino based solution is recommended.

nibegw is an application that read telegrams from a serial port (which requires an RS-485 adapter), sends ACK/NAK to the heat pump and relays untouched telegrams to openHAB via UDP packets. The Nibe Heat Pump binding will listen to a UDP port and parse register data from UDP telegrams.

Arduino

Arduino-based solution is tested with Arduino uno + RS485 and Ethernet shields. Also ProDiNo NetBoards are supported. ProDiNo have both Ethernet and RS-485 ports on the board.

Arduino code is available here

Arduino code can be builded via Arduino IDE. See more details from www.arduino.cc. NibeGW configuration(such IP addresses, ports, etc) can be adapted directly editing the code files.

Raspberry Pi (or other Linux/Unix based boards)

C code is available on here

build C code:

gcc -std=gnu99 -o nibegw nibegw.c

help:

nibegw -h

./nibegw usage:

    -h                 Print help
    -v                 Print debug information
    -d <device name>   Serial port device (default: /dev/ttyS0)
    -a <address>       Remote host address (default: 127.0.0.1)
    -p <port>          Remote UDP port (default: 9999)
    -f                 Disable flow control (default: HW)
    -r <address>       RS-485 address to listen (default: 0x20)
    -i                 Send all messages by UDP (default: only modbus data)
    -n                 Don't send acknowledge at all
    -o                 Send acknowledge to all addresses
    -t                 Test mode
    -l <port>          Local UDP port for read commands (default: 9999)
    -w <port>          Local UDP port for write commands (default: 10000)
    -q                 Print data in log format

run example:

nibegw -v -d /dev/ttyUSB0 -a 192.168.1.10

Binding Configuration

No binding configuration required.

Thing Configuration

Things can be fully configured via Paper Ui, but following information is usefull if you want to configure things via thing configuration files.

UDP connection

Thing examples:

nibeheatpump:f1x45-udp:myPump [hostName="192.168.1.50", port=9999]
nibeheatpump:f1x45-udp:myPump [hostName="192.168.1.50", port=9999, readCommandsPort=10000, writeCommandsPort=10001, refreshInterval=30, enableReadCommands=true, enableWriteCommands=true, enableRegistersForWriteCommands="44266, 47004"]

All supported configuration parameters for UDP connection:

Property Type Default Required Description
hostName String Yes Network address of the Nibe heat pump
port Integer 9999 No UDP port to listening data packets from the NibeGW
readCommandsPort Integer 9999 No UDP port to send read commands to the NibeGW
writeCommandsPort Integer 10000 No UDP port to send write commands to the NibeGW
refreshInterval Integer 60 No States how often a refresh shall occur in seconds
enableReadCommands Boolean false No Enable read commands to read additional variable from Nibe heat pump which are not included to data readout messages. This is experimental feature, use it at your own risk!
enableWriteCommands Boolean false No Enable write commands to change Nibe heat pump settings. This is experimental feature, use it at your own risk!
enableRegistersForWriteCommands String No Comma separated list of registers, which are allowed to write to Nibe heat pump. E.g. 44266, 47004
throttleTime Integer 0 No Throttle incoming data read out messages from heat pump. 0 = throttle is disabled, otherwise throttle time in milliseconds.

Serial port connection

Thing example:

nibeheatpump:f1x45-serial:myPump [serialPort="/dev/ttyUSB0"]

All supported configuration parameters for serial port connection:

Property Type Default Required Description
serialPort String Yes Network address of the Nibe heat pump
refreshInterval Integer 60 No States how often a refresh shall occur in seconds
enableReadCommands Boolean false No Enable read commands to read additional variable from Nibe heat pump which are not included to data readout messages. This is experimental feature, use it at your own risk!
enableWriteCommands Boolean false No Enable write commands to change Nibe heat pump settings. This is experimental feature, use it at your own risk!
enableRegistersForWriteCommands String No Comma separated list of registers, which are allowed to write to Nibe heat pump. E.g. 44266, 47004
sendAckToMODBUS40 Boolean true No Binding emulates MODBUS40 device and send protocol acknowledges to heat pump
sendAckToRMU40 Boolean false No Binding emulates RMU40 device and send protocol acknowledges to heat pump
sendAckToSMS40 Boolean false No Binding emulates SMS40 device and send protocol acknowledges to heat pump
throttleTime Integer 0 No Throttle incoming data read out messages from heat pump. 0 = throttle is disabled, otherwise throttle time in milliseconds.

Channels

This binding currently supports following channels for F1x45 pump models:

Channel Type ID Item Type Min Max Type Description Values
40004 Number -32767 32767 Setting BT1 Outdoor temp
40005 Number -32767 32767 Setting EP23-BT2 Supply temp S4
40006 Number -32767 32767 Setting EP22-BT2 Supply temp S3
40007 Number -32767 32767 Setting EP21-BT2 Supply temp S2
40008 Number -32767 32767 Setting BT2 Supply temp S1
40012 Number -32767 32767 Setting EB100-EP14-BT3 Return temp
40013 Number -32767 32767 Setting BT7 Hot Water top
40014 Number -32767 32767 Setting BT6 Hot Water load
40015 Number -32767 32767 Setting EB100-EP14-BT10 Brine in temp
40016 Number -32767 32767 Setting EB100-EP14-BT11 Brine out temp
40017 Number -32767 32767 Setting EB100-EP14-BT12 Cond. out
40018 Number -32767 32767 Setting EB100-EP14-BT14 Hot gas temp
40019 Number -32767 32767 Setting EB100-EP14-BT15 Liquid line
40022 Number -32767 32767 Setting EB100-EP14-BT17 Suction
40025 Number -32767 32767 Setting EB100-BT20 Exhaust air temp. 1
40026 Number -32767 32767 Setting EB100-BT21 Vented air temp. 1
40028 Number -32767 32767 Setting AZ1-BT26 Temp Collector in FLM 1
40029 Number -32767 32767 Setting AZ1-BT27 Temp Collector out FLM 1
40030 Number -32767 32767 Setting EP23-BT50 Room Temp S4
40031 Number -32767 32767 Setting EP22-BT50 Room Temp S3
40032 Number -32767 32767 Setting EP21-BT50 Room Temp S2
40033 Number -32767 32767 Setting BT50 Room Temp S1
40042 Number -32767 32767 Setting CL11-BT51 Pool 1 Temp
40043 Number -32767 32767 Setting EP8-BT53 Solar Panel Temp
40044 Number -32767 32767 Setting EP8-BT54 Solar Load Temp
40045 Number -32767 32767 Setting EQ1-BT64 Cool Supply Temp
40046 Number -32767 32767 Setting EQ1-BT65 Cool Return Temp
40054 Number -32767 32767 Setting EB100-FD1 Temperature limiter
40067 Number -32767 32767 Setting BT1 Average
40070 Number -32767 32767 Setting EM1-BT52 Boiler temperature
40071 Number -32767 32767 Setting BT25 external supply temp
40072 Number -32767 32767 Setting BF1 Flow
40074 Number -32767 32767 Setting EB100-FR1 Anode Status
40079 Number -2147483648 2147483647 Setting EB100-BE3 Current Phase 3
40081 Number -2147483648 2147483647 Setting EB100-BE2 Current Phase 2
40083 Number -2147483648 2147483647 Setting EB100-BE1 Current Phase 1
40106 Number -32767 32767 Setting CL12-BT51 Pool 2 Temp
40107 Number -32767 32767 Setting EB100-BT20 Exhaust air temp. 4
40108 Number -32767 32767 Setting EB100-BT20 Exhaust air temp. 3
40109 Number -32767 32767 Setting EB100-BT20 Exhaust air temp. 2
40110 Number -32767 32767 Setting EB100-BT21 Vented air temp. 4
40111 Number -32767 32767 Setting EB100-BT21 Vented air temp. 3
40112 Number -32767 32767 Setting EB100-BT21 Vented air temp. 2
40113 Number -32767 32767 Setting AZ4-BT26 Temp Collector in FLM 4
40114 Number -32767 32767 Setting AZ3-BT26 Temp Collector in FLM 3
40115 Number -32767 32767 Setting AZ2-BT26 Temp Collector in FLM 2
40116 Number -32767 32767 Setting AZ4-BT27 Temp Collector out FLM 4
40117 Number -32767 32767 Setting AZ3-BT27 Temp Collector out FLM 3
40118 Number -32767 32767 Setting AZ2-BT27 Temp Collector out FLM 2
40127 Number -32767 32767 Setting EP23-BT3 Return temp S4
40128 Number -32767 32767 Setting EP22-BT3 Return temp S3
40129 Number -32767 32767 Setting EP21-BT3 Return temp S2
40155 Number -32767 32767 Setting EQ1-BT57 Collector temp.
40156 Number -32767 32767 Setting EQ1-BT75 Heatdump temp.
43001 Number 0 65535 Setting Software version
43005 Number -30000 30000 Setting Degree Minutes
43006 Number -32767 32767 Setting Calculated Supply Temperature S4
43007 Number -32767 32767 Setting Calculated Supply Temperature S3
43008 Number -32767 32767 Setting Calculated Supply Temperature S2
43009 Number -32767 32767 Setting Calculated Supply Temperature S1
43013 String 0 255 Setting Freeze Protection Status 1=Freeze protection active
43024 String 0 255 Setting Status Cooling 0=Off, 1=On
43081 Number 0 9999999 Setting Tot. op.time add.
43084 Number -32767 32767 Setting Int. el.add. Power
43086 String 0 255 Setting Prio 10=Off, 20=Hot Water, 30=Heat, 40=Pool, 41=Pool 2, 50=Transfer, 60=Cooling
43091 Number 0 255 Setting Int. el.add. State
43097 String 0 255 Setting Status of the shunt controlled additional heat accessory 10=Off, 20=Running, 30=Passive
43103 Number 0 255 Setting HPAC state
43108 Number 0 255 Setting Fan speed current
43152 Number 0 255 Setting Internal cooling blocked
43158 Number 0 255 Setting External adjustment activated via input S4
43159 Number 0 255 Setting External adjustment activated via input S3
43160 Number 0 255 Setting External adjustment activated via input S2
43161 Number 0 255 Setting External adjustment activated via input S1
43163 String 0 255 Setting Blocking status of the shunt controlled add heat acc 0=Unblocked, 1=Blocked
43164 Number 0 255 Setting Cooling blocked
43171 String 0 255 Setting Blocking status of the step controlled add heat acc 0=Unblocked, 1=Blocked
43189 String 0 255 Setting Ext. Heat Medium Pump 0=Off, 1=On
43230 Number 0 9999999 Setting Accumulated energy
43239 Number 0 9999999 Setting Tot. HW op.time add.
43395 Number 0 255 Setting HPAC Relays
43416 Number 0 9999999 Setting Compressor starts EB100-EP14
43420 Number 0 9999999 Setting Tot. op.time compr. EB100-EP14
43424 Number 0 9999999 Setting Tot. HW op.time compr. EB100-EP14
43427 String 0 255 Setting Compressor State EP14 20=Stopped, 40=Starting, 60=Running, 100=Stopping
43431 Number 0 255 Setting Supply Pump State EP14
43433 Number 0 255 Setting Brine pump state EP14
43435 String 0 255 Setting Compressor status EP14 0=Off, 1=On
43437 Number 0 255 Setting HM-pump Status EP14
43439 Number 0 255 Setting Brinepump Status EP14
43473 Number 0 255 Setting Heat Compressors
43474 Number 0 255 Setting Hot Water Compressors
43475 Number 0 255 Setting Pool 1 Compressors
43484 Number 0 255 Setting FLM Cooling Activated
43485 Number 0 255 Setting FLM Cooling Activated
43486 Number 0 255 Setting FLM Cooling Activated
43487 Number 0 255 Setting FLM Cooling Activated
43514 Number 0 255 Setting PCA-Base Relays EP14
43516 Number 0 255 Setting PCA-Power Relays EP14
43560 Number 0 255 Setting Pool 2 blocked
43561 Number 0 255 Setting Pool 1 blocked
43563 Number 0 255 Setting Pool 2 valve
43564 Number 0 255 Setting Pool 1 valve
43577 Number 0 255 Setting Pool 2 Compressors
43580 Number 0 65535 Setting EB108 Version
43598 Number 0 255 Setting EB108 Slave Type
43599 Number 0 255 Setting EB108 Compressor Size
43600 Number -32767 32767 Setting EB108-EP15-BT3 Return temp.
43601 Number -32767 32767 Setting EB108-EP15-BT10 Brine in temp
43602 Number -32767 32767 Setting EB108-EP15-BT11 Brine out temp
43603 Number -32767 32767 Setting EB108-EP15-BT12 Cond. out
43604 Number -32767 32767 Setting EB108-EP15-BT14 Hot gas temp
43605 Number -32767 32767 Setting EB108-EP15-BT15 Liquid line
43606 Number -32767 32767 Setting EB108-EP15-BT17 Suction
43607 Number -32767 32767 Setting EB108-EP15-BT29 Compr. Oil. temp.
43608 Number -32767 32767 Setting EB108-EP15-BP8 Pressure transmitter
43609 Number 0 255 Setting EB108-EP15 Compressor State
43610 Number 0 255 Setting EB108-EP15 Compr. time to start
43611 Number 0 65535 Setting EB108-EP15 Relay status
43612 Number 0 255 Setting EB108-EP15 Heat med. pump status
43613 Number 0 255 Setting EB108-EP15 Brine pump status
43614 Number 0 4294967295 Setting EB108-EP15 Compressor starts
43616 Number 0 4294967295 Setting EB108-EP15 Tot. op.time compr
43618 Number 0 4294967295 Setting EB108-EP15 Tot. HW op.time compr
43620 Number 0 65535 Setting EB108-EP15 Alarm number
43621 Number -32767 32767 Setting EB108-EP14-BT3 Return temp.
43622 Number -32767 32767 Setting EB108-EP14-BT10 Brine in temp
43623 Number -32767 32767 Setting EB108-EP14-BT11 Brine out temp
43624 Number -32767 32767 Setting EB108-EP14-BT12 Cond. out
43625 Number -32767 32767 Setting EB108-EP14-BT14 Hot gas temp
43626 Number -32767 32767 Setting EB108-EP14-BT15 Liquid line
43627 Number -32767 32767 Setting EB108-EP14-BT17 Suction
43628 Number -32767 32767 Setting EB108-EP14-BT29 Compr. Oil. temp.
43629 Number -32767 32767 Setting EB108-EP14-BP8 Pressure transmitter
43630 Number 0 255 Setting EB108-EP14 Compressor State
43631 Number 0 255 Setting EB108-EP14 Compr. time to start
43632 Number 0 65535 Setting EB108-EP14 Relay status
43633 Number 0 255 Setting EB108-EP14 Heat med. pump status
43634 Number 0 255 Setting EB108-EP14 Brine pump status
43635 Number 0 9999999 Setting EB108-EP14 Compressor starts
43637 Number 0 9999999 Setting EB108-EP14 Tot. op.time compr
43639 Number 0 9999999 Setting EB108-EP14 Tot. HW op.time compr
43641 Number 0 65535 Setting EB108-EP14 Alarm number
43642 Number 0 65535 Setting EB107 Version
43660 Number 0 255 Setting EB107 Slave Type
43661 Number 0 255 Setting EB107 Compressor Size
43662 Number -32767 32767 Setting EB107-EP15-BT3 Return temp.
43663 Number -32767 32767 Setting EB107-EP15-BT10 Brine in temp
43664 Number -32767 32767 Setting EB107-EP15-BT11 Brine out temp
43665 Number -32767 32767 Setting EB107-EP15-BT12 Cond. out
43666 Number -32767 32767 Setting EB107-EP15-BT14 Hot gas temp
43667 Number -32767 32767 Setting EB107-EP15-BT15 Liquid line
43668 Number -32767 32767 Setting EB107-EP15-BT17 Suction
43669 Number -32767 32767 Setting EB107-EP15-BT29 Compr. Oil. temp.
43670 Number -32767 32767 Setting EB107-EP15-BP8 Pressure transmitter
43671 Number 0 255 Setting EB107-EP15 Compressor State
43672 Number 0 255 Setting EB107-EP15 Compr. time to start
43673 Number 0 65535 Setting EB107-EP15 Relay status
43674 Number 0 255 Setting EB107-EP15 Heat med. pump status
43675 Number 0 255 Setting EB107-EP15 Brine pump status
43676 Number 0 4294967295 Setting EB107-EP15 Compressor starts
43678 Number 0 4294967295 Setting EB107-EP15 Tot. op.time compr
43680 Number 0 4294967295 Setting EB107-EP15 Tot. HW op.time compr
43682 Number 0 65535 Setting EB107-EP15 Alarm number
43683 Number -32767 32767 Setting EB107-EP14-BT3 Return temp.
43684 Number -32767 32767 Setting EB107-EP14-BT10 Brine in temp
43685 Number -32767 32767 Setting EB107-EP14-BT11 Brine out temp
43686 Number -32767 32767 Setting EB107-EP14-BT12 Cond. out
43687 Number -32767 32767 Setting EB107-EP14-BT14 Hot gas temp
43688 Number -32767 32767 Setting EB107-EP14-BT15 Liquid line
43689 Number -32767 32767 Setting EB107-EP14-BT17 Suction
43690 Number -32767 32767 Setting EB107-EP14-BT29 Compr. Oil. temp.
43691 Number -32767 32767 Setting EB107-EP14-BP8 Pressure transmitter
43692 Number 0 255 Setting EB107-EP14 Compressor State
43693 Number 0 255 Setting EB107-EP14 Compr. time to start
43694 Number 0 65535 Setting EB107-EP14 Relay status
43695 Number 0 255 Setting EB107-EP14 Heat med. pump status
43696 Number 0 255 Setting EB107-EP14 Brine pump status
43697 Number 0 9999999 Setting EB107-EP14 Compressor starts
43699 Number 0 9999999 Setting EB107-EP14 Tot. op.time compr
43701 Number 0 9999999 Setting EB107-EP14 Tot. HW op.time compr
43703 Number 0 65535 Setting EB107-EP14 Alarm number
43704 Number 0 65535 Setting EB106 Version
43722 Number 0 255 Setting EB106 Slave Type
43723 Number 0 255 Setting EB106 Compressor Size
43724 Number -32767 32767 Setting EB106-EP15-BT3 Return temp.
43725 Number -32767 32767 Setting EB106-EP15-BT10 Brine in temp
43726 Number -32767 32767 Setting EB106-EP15-BT11 Brine out temp
43727 Number -32767 32767 Setting EB106-EP15-BT12 Cond. out
43728 Number -32767 32767 Setting EB106-EP15-BT14 Hot gas temp
43729 Number -32767 32767 Setting EB106-EP15-BT15 Liquid line
43730 Number -32767 32767 Setting EB106-EP15-BT17 Suction
43731 Number -32767 32767 Setting EB106-EP15-BT29 Compr. Oil. temp.
43732 Number -32767 32767 Setting EB106-EP15-BP8 Pressure transmitter
43733 Number 0 255 Setting EB106-EP15 Compressor State
43734 Number 0 255 Setting EB106-EP15 Compr. time to start
43735 Number 0 65535 Setting EB106-EP15 Relay status
43736 Number 0 255 Setting EB106-EP15 Heat med. pump status
43737 Number 0 255 Setting EB106-EP15 Brine pump status
43738 Number 0 4294967295 Setting EB106-EP15 Compressor starts
43740 Number 0 4294967295 Setting EB106-EP15 Tot. op.time compr
43742 Number 0 4294967295 Setting EB106-EP15 Tot. HW op.time compr
43744 Number 0 65535 Setting EB106-EP15 Alarm number
43745 Number -32767 32767 Setting EB106-EP14-BT3 Return temp.
43746 Number -32767 32767 Setting EB106-EP14-BT10 Brine in temp
43747 Number -32767 32767 Setting EB106-EP14-BT11 Brine out temp
43748 Number -32767 32767 Setting EB106-EP14-BT12 Cond. out
43749 Number -32767 32767 Setting EB106-EP14-BT14 Hot gas temp
43750 Number -32767 32767 Setting EB106-EP14-BT15 Liquid line
43751 Number -32767 32767 Setting EB106-EP14-BT17 Suction
43752 Number -32767 32767 Setting EB106-EP14-BT29 Compr. Oil. temp.
43753 Number -32767 32767 Setting EB106-EP14-BP8 Pressure transmitter
43754 Number 0 255 Setting EB106-EP14 Compressor State
43755 Number 0 255 Setting EB106-EP14 Compr. time to start
43756 Number 0 65535 Setting EB106-EP14 Relay status
43757 Number 0 255 Setting EB106-EP14 Heat med. pump status
43758 Number 0 255 Setting EB106-EP14 Brine pump status
43759 Number 0 9999999 Setting EB106-EP14 Compressor starts
43761 Number 0 9999999 Setting EB106-EP14 Tot. op.time compr
43763 Number 0 9999999 Setting EB106-EP14 Tot. HW op.time compr
43765 Number 0 65535 Setting EB106-EP14 Alarm number
43766 Number 0 65535 Setting EB105 Version
43784 Number 0 255 Setting EB105 Slave Type
43785 Number 0 255 Setting EB105 Compressor Size
43786 Number -32767 32767 Setting EB105-EP15-BT3 Return temp.
43787 Number -32767 32767 Setting EB105-EP15-BT10 Brine in temp
43788 Number -32767 32767 Setting EB105-EP15-BT11 Brine out temp
43789 Number -32767 32767 Setting EB105-EP15-BT12 Cond. out
43790 Number -32767 32767 Setting EB105-EP15-BT14 Hot gas temp
43791 Number -32767 32767 Setting EB105-EP15-BT15 Liquid line
43792 Number -32767 32767 Setting EB105-EP15-BT17 Suction
43793 Number -32767 32767 Setting EB105-EP15-BT29 Compr. Oil. temp.
43794 Number -32767 32767 Setting EB105-EP15-BP8 Pressure transmitter
43795 Number 0 255 Setting EB105-EP15 Compressor State
43796 Number 0 255 Setting EB105-EP15 Compr. time to start
43797 Number 0 65535 Setting EB105-EP15 Relay status
43798 Number 0 255 Setting EB105-EP15 Heat med. pump status
43799 Number 0 255 Setting EB105-EP15 Brine pump status
43800 Number 0 4294967295 Setting EB105-EP15 Compressor starts
43802 Number 0 4294967295 Setting EB105-EP15 Tot. op.time compr
43804 Number 0 4294967295 Setting EB105-EP15 Tot. HW op.time compr
43806 Number 0 65535 Setting EB105-EP15 Alarm number
43807 Number -32767 32767 Setting EB105-EP14-BT3 Return temp.
43808 Number -32767 32767 Setting EB105-EP14-BT10 Brine in temp
43809 Number -32767 32767 Setting EB105-EP14-BT11 Brine out temp
43810 Number -32767 32767 Setting EB105-EP14-BT12 Cond. out
43811 Number -32767 32767 Setting EB105-EP14-BT14 Hot gas temp
43812 Number -32767 32767 Setting EB105-EP14-BT15 Liquid line
43813 Number -32767 32767 Setting EB105-EP14-BT17 Suction
43814 Number -32767 32767 Setting EB105-EP14-BT29 Compr. Oil. temp.
43815 Number -32767 32767 Setting EB105-EP14-BP8 Pressure transmitter
43816 Number 0 255 Setting EB105-EP14 Compressor State
43817 Number 0 255 Setting EB105-EP14 Compr. time to start
43818 Number 0 65535 Setting EB105-EP14 Relay status
43819 Number 0 255 Setting EB105-EP14 Heat med. pump status
43820 Number 0 255 Setting EB105-EP14 Brine pump status
43821 Number 0 9999999 Setting EB105-EP14 Compressor starts
43823 Number 0 9999999 Setting EB105-EP14 Tot. op.time compr
43825 Number 0 9999999 Setting EB105-EP14 Tot. HW op.time compr
43827 Number 0 65535 Setting EB105-EP14 Alarm number
43828 Number 0 65535 Setting EB104 Version
43846 Number 0 255 Setting EB104 Slave Type
43847 Number 0 255 Setting EB104 Compressor Size
43848 Number -32767 32767 Setting EB104-EP15-BT3 Return temp.
43849 Number -32767 32767 Setting EB104-EP15-BT10 Brine in temp
43850 Number -32767 32767 Setting EB104-EP15-BT11 Brine out temp
43851 Number -32767 32767 Setting EB104-EP15-BT12 Cond. out
43852 Number -32767 32767 Setting EB104-EP15-BT14 Hot gas temp
43853 Number -32767 32767 Setting EB104-EP15-BT15 Liquid line
43854 Number -32767 32767 Setting EB104-EP15-BT17 Suction
43855 Number -32767 32767 Setting EB104-EP15-BT29 Compr. Oil. temp.
43856 Number -32767 32767 Setting EB104-EP15-BP8 Pressure transmitter
43857 Number 0 255 Setting EB104-EP15 Compressor State
43858 Number 0 255 Setting EB104-EP15 Compr. time to start
43859 Number 0 65535 Setting EB104-EP15 Relay status
43860 Number 0 255 Setting EB104-EP15 Heat med. pump status
43861 Number 0 255 Setting EB104-EP15 Brine pump status
43862 Number 0 4294967295 Setting EB104-EP15 Compressor starts
43864 Number 0 4294967295 Setting EB104-EP15 Tot. op.time compr
43866 Number 0 4294967295 Setting EB104-EP15 Tot. HW op.time compr
43868 Number 0 65535 Setting EB104-EP15 Alarm number
43869 Number -32767 32767 Setting EB104-EP14-BT3 Return temp.
43870 Number -32767 32767 Setting EB104-EP14-BT10 Brine in temp
43871 Number -32767 32767 Setting EB104-EP14-BT11 Brine out temp
43872 Number -32767 32767 Setting EB104-EP14-BT12 Cond. out
43873 Number -32767 32767 Setting EB104-EP14-BT14 Hot gas temp
43874 Number -32767 32767 Setting EB104-EP14-BT15 Liquid line
43875 Number -32767 32767 Setting EB104-EP14-BT17 Suction
43876 Number -32767 32767 Setting EB104-EP14-BT29 Compr. Oil. temp.
43877 Number -32767 32767 Setting EB104-EP14-BP8 Pressure transmitter
43878 Number 0 255 Setting EB104-EP14 Compressor State
43879 Number 0 255 Setting EB104-EP14 Compr. time to start
43880 Number 0 65535 Setting EB104-EP14 Relay status
43881 Number 0 255 Setting EB104-EP14 Heat med. pump status
43882 Number 0 255 Setting EB104-EP14 Brine pump status
43883 Number 0 9999999 Setting EB104-EP14 Compressor starts
43885 Number 0 9999999 Setting EB104-EP14 Tot. op.time compr
43887 Number 0 9999999 Setting EB104-EP14 Tot. HW op.time compr
43889 Number 0 65535 Setting EB104-EP14 Alarm number
43890 Number 0 65535 Setting EB103 Version
43908 Number 0 255 Setting EB103 Slave Type
43909 Number 0 255 Setting EB103 Compressor Size
43910 Number -32767 32767 Setting EB103-EP15-BT3 Return temp.
43911 Number -32767 32767 Setting EB103-EP15-BT10 Brine in temp
43912 Number -32767 32767 Setting EB103-EP15-BT11 Brine out temp
43913 Number -32767 32767 Setting EB103-EP15-BT12 Cond. out
43914 Number -32767 32767 Setting EB103-EP15-BT14 Hot gas temp
43915 Number -32767 32767 Setting EB103-EP15-BT15 Liquid line
43916 Number -32767 32767 Setting EB103-EP15-BT17 Suction
43917 Number -32767 32767 Setting EB103-EP15-BT29 Compr. Oil. temp.
43918 Number -32767 32767 Setting EB103-EP15-BP8 Pressure transmitter
43919 Number 0 255 Setting EB103-EP15 Compressor State
43920 Number 0 255 Setting EB103-EP15 Compr. time to start
43921 Number 0 65535 Setting EB103-EP15 Relay status
43922 Number 0 255 Setting EB103-EP15 Heat med. pump status
43923 Number 0 255 Setting EB103-EP15 Brine pump status
43924 Number 0 4294967295 Setting EB103-EP15 Compressor starts
43926 Number 0 4294967295 Setting EB103-EP15 Tot. op.time compr
43928 Number 0 4294967295 Setting EB103-EP15 Tot. HW op.time compr
43930 Number 0 65535 Setting EB103-EP15 Alarm number
43931 Number -32767 32767 Setting EB103-EP14-BT3 Return temp.
43932 Number -32767 32767 Setting EB103-EP14-BT10 Brine in temp
43933 Number -32767 32767 Setting EB103-EP14-BT11 Brine out temp
43934 Number -32767 32767 Setting EB103-EP14-BT12 Cond. out
43935 Number -32767 32767 Setting EB103-EP14-BT14 Hot gas temp
43936 Number -32767 32767 Setting EB103-EP14-BT15 Liquid line
43937 Number -32767 32767 Setting EB103-EP14-BT17 Suction
43938 Number -32767 32767 Setting EB103-EP14-BT29 Compr. Oil. temp.
43939 Number -32767 32767 Setting EB103-EP14-BP8 Pressure transmitter
43940 Number 0 255 Setting EB103-EP14 Compressor State
43941 Number 0 255 Setting EB103-EP14 Compr. time to start
43942 Number 0 65535 Setting EB103-EP14 Relay status
43943 Number 0 255 Setting EB103-EP14 Heat med. pump status
43944 Number 0 255 Setting EB103-EP14 Brine pump status
43945 Number 0 9999999 Setting EB103-EP14 Compressor starts
43947 Number 0 9999999 Setting EB103-EP14 Tot. op.time compr
43949 Number 0 9999999 Setting EB103-EP14 Tot. HW op.time compr
43951 Number 0 65535 Setting EB103-EP14 Alarm number
43952 Number 0 65535 Setting EB102 Version
43970 Number 0 255 Setting EB102 Slave Type
43971 Number 0 255 Setting EB102 Compressor Size
43972 Number -32767 32767 Setting EB102-EP15-BT3 Return temp.
43973 Number -32767 32767 Setting EB102-EP15-BT10 Brine in temp
43974 Number -32767 32767 Setting EB102-EP15-BT11 Brine out temp
43975 Number -32767 32767 Setting EB102-EP15-BT12 Cond. out
43976 Number -32767 32767 Setting EB102-EP15-BT14 Hot gas temp
43977 Number -32767 32767 Setting EB102-EP15-BT15 Liquid line
43978 Number -32767 32767 Setting EB102-EP15-BT17 Suction
43979 Number -32767 32767 Setting EB102-EP15-BT29 Compr. Oil. temp.
43980 Number -32767 32767 Setting EB102-EP15-BP8 Pressure transmitter
43981 Number 0 255 Setting EB102-EP15 Compressor State
43982 Number 0 255 Setting EB102-EP15 Compr. time to start
43983 Number 0 65535 Setting EB102-EP15 Relay status
43984 Number 0 255 Setting EB102-EP15 Heat med. pump status
43985 Number 0 255 Setting EB102-EP15 Brine pump status
43986 Number 0 4294967295 Setting EB102-EP15 Compressor starts
43988 Number 0 4294967295 Setting EB102-EP15 Tot. op.time compr
43990 Number 0 4294967295 Setting EB102-EP15 Tot. HW op.time compr
43992 Number 0 65535 Setting EB102-EP15 Alarm number
43993 Number -32767 32767 Setting EB102-EP14-BT3 Return temp.
43994 Number -32767 32767 Setting EB102-EP14-BT10 Brine in temp
43995 Number -32767 32767 Setting EB102-EP14-BT11 Brine out temp
43996 Number -32767 32767 Setting EB102-EP14-BT12 Cond. out
43997 Number -32767 32767 Setting EB102-EP14-BT14 Hot gas temp
43998 Number -32767 32767 Setting EB102-EP14-BT15 Liquid line
43999 Number -32767 32767 Setting EB102-EP14-BT17 Suction
44000 Number -32767 32767 Setting EB102-EP14-BT29 Compr. Oil. temp.
44001 Number -32767 32767 Setting EB102-EP14-BP8 Pressure transmitter
44002 Number 0 255 Setting EB102-EP14 Compressor State
44003 Number 0 255 Setting EB102-EP14 Compr. time to start
44004 Number 0 65535 Setting EB102-EP14 Relay status
44005 Number 0 255 Setting EB102-EP14 Heat med. pump status
44006 Number 0 255 Setting EB102-EP14 Brine pump status
44007 Number 0 9999999 Setting EB102-EP14 Compressor starts
44009 Number 0 9999999 Setting EB102-EP14 Tot. op.time compr
44011 Number 0 9999999 Setting EB102-EP14 Tot. HW op.time compr
44013 Number 0 65535 Setting EB102-EP14 Alarm number
44014 Number 0 65535 Setting EB101 Version
44032 Number 0 255 Setting EB101 Slave Type
44033 Number 0 255 Setting EB101 Compressor Size
44034 Number -32767 32767 Setting EB101-EP15-BT3 Return temp.
44035 Number -32767 32767 Setting EB101-EP15-BT10 Brine in temp
44036 Number -32767 32767 Setting EB101-EP15-BT11 Brine out temp
44037 Number -32767 32767 Setting EB101-EP15-BT12 Cond. out
44038 Number -32767 32767 Setting EB101-EP15-BT14 Hot gas temp
44039 Number -32767 32767 Setting EB101-EP15-BT15 Liquid line
44040 Number -32767 32767 Setting EB101-EP15-BT17 Suction
44041 Number -32767 32767 Setting EB101-EP15-BT29 Compr. Oil. temp.
44042 Number -32767 32767 Setting EB101-EP15-BP8 Pressure transmitter
44043 Number 0 255 Setting EB101-EP15 Compressor State
44044 Number 0 255 Setting EB101-EP15 Compr. time to start
44045 Number 0 65535 Setting EB101-EP15 Relay status
44046 Number 0 255 Setting EB101-EP15 Heat med. pump status
44047 Number 0 255 Setting EB101-EP15 Brine pump status
44048 Number 0 4294967295 Setting EB101-EP15 Compressor starts
44050 Number 0 4294967295 Setting EB101-EP15 Tot. op.time compr
44052 Number 0 4294967295 Setting EB101-EP15 Tot. HW op.time compr
44054 Number 0 65535 Setting EB101-EP15 Alarm number
44055 Number -32767 32767 Setting EB101-EP14-BT3 Return temp.
44056 Number -32767 32767 Setting EB101-EP14-BT10 Brine in temp
44057 Number -32767 32767 Setting EB101-EP14-BT11 Brine out temp
44058 Number -32767 32767 Setting EB101-EP14-BT12 Cond. out
44059 Number -32767 32767 Setting EB101-EP14-BT14 Hot gas temp
44060 Number -32767 32767 Setting EB101-EP14-BT15 Liquid line
44061 Number -32767 32767 Setting EB101-EP14-BT17 Suction
44062 Number -32767 32767 Setting EB101-EP14-BT29 Compr. Oil. temp.
44063 Number -32767 32767 Setting EB101-EP14-BP8 Pressure transmitter
44064 Number 0 255 Setting EB101-EP14 Compressor State
44065 Number 0 255 Setting EB101-EP14 Compr. time to start
44066 Number 0 65535 Setting EB101-EP14 Relay status
44067 Number 0 255 Setting EB101-EP14 Heat med. pump status
44068 Number 0 255 Setting EB101-EP14 Brine pump status
44069 Number 0 9999999 Setting EB101-EP14 Compressor starts
44071 Number 0 9999999 Setting EB101-EP14 Tot. op.time compr
44073 Number 0 9999999 Setting EB101-EP14 Tot. HW op.time compr
44075 Number 0 65535 Setting EB101-EP14 Alarm number
44138 String 0 255 Setting EB108-EP15 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44139 String 0 255 Setting EB108-EP14 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44151 String 0 255 Setting EB107-EP15 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44152 String 0 255 Setting EB107-EP14 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44164 String 0 255 Setting EB106-EP15 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44165 String 0 255 Setting EB106-EP14 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44177 String 0 255 Setting EB105-EP15 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44178 String 0 255 Setting EB105-EP14 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44190 String 0 255 Setting EB104-EP15 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44191 String 0 255 Setting EB104-EP14 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44203 String 0 255 Setting EB103-EP15 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44204 String 0 255 Setting EB103-EP14 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44216 String 0 255 Setting EB102-EP15 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44217 String 0 255 Setting EB102-EP14 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44229 String 0 255 Setting EB101-EP15 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44230 String 0 255 Setting EB101-EP14 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44242 String 0 255 Setting EB100-EP15 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44243 String 0 255 Setting EB100-EP14 Prio 0=Off, 1=Heat, 2=Hot water, 3=Pool 1, 4=Pool2
44266 Number -30000 30000 Setting Cool Degree Minutes
44267 Number -32767 32767 Setting Calc. Cooling Supply Temperature S4
44268 Number -32767 32767 Setting Calc. Cooling Supply Temperature S3
44269 Number -32767 32767 Setting Calc. Cooling Supply Temperature S2
44270 Number -32767 32767 Setting Calc. Cooling Supply Temperature S1
44276 Number 0 255 Setting State ACS
44277 Number 0 255 Setting State ACS heatdump
44278 Number 0 255 Setting State ACS cooldump
44282 Number 0 255 Setting Used cprs. HW
44283 Number 0 255 Setting Used cprs. heat
44284 Number 0 255 Setting Used cprs. pool 1
44285 Number 0 255 Setting Used cprs. pool 2
44298 Number 0 9999999 Setting Accumulated Energy HW Cpr and Add
44300 Number 0 9999999 Setting Accumulated Energy Heat Cpr and Add
44302 Number 0 9999999 Setting Accumulated Energy Cooling Cpr
44304 Number 0 9999999 Setting Accumulated Energy Pool Cpr
44306 Number 0 9999999 Setting Accumulated Energy HW Cpr
44308 Number 0 9999999 Setting Accumulated Energy Heat Cpr
44320 Number 0 255 Setting Used cprs. cool
44331 Number 0 255 Setting Software release
44380 Number 0 255 Setting External Compressors
44410 Number 0 255 Setting EB108 Own Hot Water
44411 Number -32767 32767 Setting EB108-BT6 Hot water load temp.
44412 Number -32767 32767 Setting EB108-BT7 Hot water top temp.
44413 Number -32767 32767 Setting EB108-BT2 Supply temp.
44416 Number 0 255 Setting EB107 Own Hot Water
44417 Number -32767 32767 Setting EB107-BT6 Hot water load temp.
44418 Number -32767 32767 Setting EB107-BT7 Hot water top temp.
44419 Number -32767 32767 Setting EB107-BT2 Supply temp.
44422 Number 0 255 Setting EB106 Own Hot Water
44423 Number -32767 32767 Setting EB106-BT6 Hot water load temp.
44424 Number -32767 32767 Setting EB106-BT7 Hot water top temp.
44425 Number -32767 32767 Setting EB106-BT2 Supply temp.
44428 Number 0 255 Setting EB105 Own Hot Water
44429 Number -32767 32767 Setting EB105-BT6 Hot water load temp.
44430 Number -32767 32767 Setting EB105-BT7 Hot water top temp.
44431 Number -32767 32767 Setting EB105-BT2 Supply temp.
44434 Number 0 255 Setting EB104 Own Hot Water
44435 Number -32767 32767 Setting EB104-BT6 Hot water load temp.
44436 Number -32767 32767 Setting EB104-BT7 Hot water top temp.
44437 Number -32767 32767 Setting EB104-BT2 Supply temp.
44440 Number 0 255 Setting EB103 Own Hot Water
44441 Number -32767 32767 Setting EB103-BT6 Hot water load temp.
44442 Number -32767 32767 Setting EB103-BT7 Hot water top temp.
44443 Number -32767 32767 Setting EB103-BT2 Supply temp.
44446 Number 0 255 Setting EB102 Own Hot Water
44447 Number -32767 32767 Setting EB102-BT6 Hot water load temp.
44448 Number -32767 32767 Setting EB102-BT7 Hot water top temp.
44449 Number -32767 32767 Setting EB102-BT2 Supply temp.
44452 Number 0 255 Setting EB101 Own Hot Water
44453 Number -32767 32767 Setting EB101-BT6 Hot water load temp.
44454 Number -32767 32767 Setting EB101-BT7 Hot water top temp.
44455 Number -32767 32767 Setting EB101-BT2 Supply temp.
44487 Number 0 255 Setting Cool Compressors
44744 Number 0 255 Setting Extra heating system pump S4
44745 Number 0 255 Setting Extra heating system pump S3
44746 Number 0 255 Setting Extra heating system pump S2
44748 Number 0 255 Setting Pool 2 pump
44749 Number 0 255 Setting Pool 1 pump
44753 Number 0 255 Setting Passiv cool shunt
44754 Number 0 255 Setting Passiv cool pool
44756 Number 0 255 Setting State ground water pump
44874 Number 0 255 Setting State SG Ready
44878 Number 0 255 Setting SG Ready input A
44879 Number 0 255 Setting SG Ready input B
44910 Number -32767 32767 Setting Brine pump dT act.
44911 Number -32767 32767 Setting Brine pump dT act.
44912 Switch 0 1 Sensor Brine pump auto controlled
45001 Number -32767 32767 Sensor Alarm Number
47291 Number 0 10000 Sensor Floor drying timer
47325 Number 0 7 Sensor Step controlled add. max. step
47004 Number 0 15 Sensor Heat curve S4
47005 Number 0 15 Sensor Heat curve S3
47006 Number 0 15 Sensor Heat curve S2
47007 Number 0 15 Sensor Heat curve S1
47008 Number -10 10 Sensor Offset S4
47009 Number -10 10 Sensor Offset S3
47010 Number -10 10 Sensor Offset S2
47011 Number -10 10 Sensor Offset S1
47012 Number 50 700 Sensor Min Supply System 4
47013 Number 50 700 Sensor Min Supply System 3
47014 Number 50 700 Sensor Min Supply System 2
47015 Number 50 700 Sensor Min Supply System 1
47016 Number 50 700 Sensor Max Supply System 4
47017 Number 50 700 Sensor Max Supply System 3
47018 Number 50 700 Sensor Max Supply System 2
47019 Number 50 700 Sensor Max Supply System 1
47020 Number 0 80 Sensor Own Curve P7
47021 Number 0 80 Sensor Own Curve P6
47022 Number 0 80 Sensor Own Curve P5
47023 Number 0 80 Sensor Own Curve P4
47024 Number 0 80 Sensor Own Curve P3
47025 Number 0 80 Sensor Own Curve P2
47026 Number 0 80 Sensor Own Curve P1
47027 Number -40 30 Sensor Point offset outdoor temp.
47028 Number -10 10 Sensor Point offset
47029 Number -10 10 Sensor External adjustment S4
47030 Number -10 10 Sensor External adjustment S3
47031 Number -10 10 Sensor External adjustment S2
47032 Number -10 10 Sensor External adjustment S1
47033 Number 50 300 Sensor External adjustment with room sensor S4
47034 Number 50 300 Sensor External adjustment with room sensor S3
47035 Number 50 300 Sensor External adjustment with room sensor S2
47036 Number 50 300 Sensor External adjustment with room sensor S1
47041 String 0 2 Sensor Hot water mode 0=Economy, 1=Normal, 2=Luxury
47043 Number 50 700 Sensor Start temperature HW Luxury
47044 Number 50 700 Sensor Start temperature HW Normal
47045 Number 50 700 Sensor Start temperature HW Economy
47046 Number 550 700 Sensor Stop temperature Periodic HW
47047 Number 50 700 Sensor Stop temperature HW Luxury
47048 Number 50 700 Sensor Stop temperature HW Normal
47049 Number 50 700 Sensor Stop temperature HW Economy
47050 Switch 0 1 Setting Periodic HW
47051 Number 1 90 Setting Periodic HW Interval
47054 Number 1 60 Setting Run time HWC
47055 Number 0 60 Setting Still time HWC
47131 String 0 21 Setting Language 0=English, 1=Svenska, 2=Deutsch, 3=Francais, 4=Espanol, 5=Suomi, 6=Lietuviu, 7=Cesky, 8=Polski, 9=Nederlands, 10=Norsk, 11=Dansk, 12=Eesti, 13=Latviesu, 16=Magyar
47134 Number 0 180 Setting Period HW
47135 Number 0 180 Setting Period Heat
47136 Number 0 180 Setting Period Pool
47138 String 10 40 Setting Operational mode heat medium pump 10=Intermittent, 20=Continous, 30=Economy, 40=Auto
47139 String 10 30 Setting Operational mode brine medium pump 10=Intermittent, 20=Continuous, 30=Economy, 40=Auto
47206 Number -1000 -30 Setting DM start heating
47207 Number -32767 32767 Setting DM start cooling
47208 Number -32767 32767 Setting DM start add.
47209 Number -32767 32767 Setting DM between add. steps
47210 Number -2000 -30 Setting DM start add. with shunt
47212 Number 0 4500 Setting Max int add. power
47214 Number 1 200 Setting Fuse
47261 Number 0 100 Setting Exhaust Fan speed 4
47262 Number 0 100 Setting Exhaust Fan speed 3
47263 Number 0 100 Setting Exhaust Fan speed 2
47264 Number 0 100 Setting Exhaust Fan speed 1
47265 Number 0 100 Setting Exhaust Fan speed normal
47271 Number 1 99 Setting Fan return time 4
47272 Number 1 99 Setting Fan return time 3
47273 Number 1 99 Setting Fan return time 2
47274 Number 1 99 Setting Fan return time 1
47275 Number 1 24 Setting Filter Reminder period
47276 Switch 0 1 Setting Floor drying
47277 Number 0 30 Setting Floor drying period 7
47278 Number 0 30 Setting Floor drying period 6
47279 Number 0 30 Setting Floor drying period 5
47280 Number 0 30 Setting Floor drying period 4
47281 Number 0 30 Setting Floor drying period 3
47282 Number 0 30 Setting Floor drying period 2
47283 Number 0 30 Setting Floor drying period 1
47284 Number 15 70 Setting Floor drying temp. 7
47285 Number 15 70 Setting Floor drying temp. 6
47286 Number 15 70 Setting Floor drying temp. 5
47287 Number 15 70 Setting Floor drying temp. 4
47288 Number 15 70 Setting Floor drying temp. 3
47289 Number 15 70 Setting Floor drying temp. 2
47290 Number 15 70 Setting Floor drying temp. 1
47302 Switch 0 1 Setting Climate system 2 accessory
47303 Switch 0 1 Setting Climate system 3 accessory
47304 Switch 0 1 Setting Climate system 4 accessory
47305 Number 1 100 Setting Climate system 4 mixing valve amp.
47306 Number 1 100 Setting Climate system 3 mixing valve amp.
47307 Number 1 100 Setting Climate system 2 mixing valve amp.
47308 Number 10 300 Setting Climate system 4 shunt wait
47309 Number 10 300 Setting Climate system 3 shunt wait
47310 Number 10 300 Setting Climate system 2 shunt wait
47312 Switch 0 1 Setting FLM pump
47313 Number 1 30 Setting FLM defrost
47317 Switch 0 1 Setting Shunt controlled add. accessory
47318 Number 5 90 Setting Shunt controlled add. min. temp.
47319 Number 0 48 Setting Shunt controlled add. min. runtime
47320 Number 1 100 Setting Shunt controlled add. mixing valve amp.
47321 Number 10 300 Setting Shunt controlled add. mixing valve wait
47322 Switch 0 1 Setting Step controlled add. accessory
47323 Number -2000 -30 Setting Step controlled add. start DM
47324 Number 0 1000 Setting Step controlled add. diff. DM
47326 Switch 0 1 Setting Step controlled add. mode
47327 Switch 0 1 Setting Ground water pump accessory
47329 Switch 0 1 Setting Cooling 2-pipe accessory
47330 Switch 0 1 Setting Cooling 4-pipe accessory
47335 Number 0 48 Setting Time betw. switch heat/cool
47336 Number 5 100 Setting Heat at room under temp.
47337 Number 5 100 Setting Cool at room over temp.
47338 Number 1 100 Setting Cooling mix. valve amp.
47339 Number 10 300 Setting Cooling mix. valve step delay
47340 Switch 0 1 Setting Cooling with room sensor
47341 Switch 0 1 Setting HPAC accessory
47342 Number 10 500 Setting Start Passive Cooling DM
47343 Number 30 300 Setting Start Active Cooling DM
47352 Switch 0 1 Setting SMS40 accessory
47365 Switch 0 1 Setting RMU System 1
47366 Switch 0 1 Setting RMU System 2
47367 Switch 0 1 Setting RMU System 3
47368 Switch 0 1 Setting RMU System 4
47370 Switch 0 1 Setting Allow Additive Heating
47371 Switch 0 1 Setting Allow Heating
47372 Switch 0 1 Setting Allow Cooling
47378 Number 10 250 Setting Max diff. comp.
47379 Number 10 240 Setting Max diff. add.
47380 Switch 0 1 Setting Low brine out autoreset
47381 Number -120 150 Setting Low brine out temp.
47382 Switch 0 1 Setting High brine in
47383 Number 100 300 Setting High brine in temp.
47384 String 1 2 Setting Date format 1=DD-MM-YY, 2=YY-MM-DD
47385 String 12 24 Setting Time format 12=hours 24, 24=Hours
47387 Switch 0 1 Setting HW production 12=hours 24, 24=Hours
47388 Switch 0 1 Setting Alarm lower room temp. 12=hours 24, 24=Hours
47389 Switch 0 1 Setting Alarm lower HW temp. 12=hours 24, 24=Hours
47391 Switch 0 1 Setting Use room sensor S4 12=hours 24, 24=Hours
47392 Switch 0 1 Setting Use room sensor S3 12=hours 24, 24=Hours
47393 Switch 0 1 Setting Use room sensor S2 12=hours 24, 24=Hours
47394 Switch 0 1 Setting Use room sensor S1 12=hours 24, 24=Hours
47395 Number 50 300 Setting Room sensor setpoint S4
47396 Number 50 300 Setting Room sensor setpoint S3
47397 Number 50 300 Setting Room sensor setpoint S2
47398 Number 50 300 Setting Room sensor setpoint S1
47399 Number 0 60 Setting Room sensor factor S4
47400 Number 0 60 Setting Room sensor factor S3
47401 Number 0 60 Setting Room sensor factor S2
47402 Number 0 60 Setting Room sensor factor S1
47413 Number 1 100 Setting Speed circ.pump HW
47414 Number 1 100 Setting Speed circ.pump Heat
47415 Number 70 70 Setting Speed circ.pump Pool
47416 Number 0 255 Setting Speed circ.pump Economy
47417 Number 1 100 Setting Speed circ.pump Cooling
47418 Number 1 100 Setting Speed brine pump
47537 Switch 0 1 Setting Night cooling
47538 Number 20 30 Setting Start room temp. night cooling
47539 Number 3 10 Setting Night Cooling Min. diff.
47540 Number 10 2000 Setting Heat DM diff
47543 Number 10 150 Setting Cooling DM diff
47570 String 0 255 Setting Operational mode 0=Auto, 1=Manual, 2=Add. heat only
48053 Number 0 100 Setting FLM 2 speed 4
48054 Number 0 100 Setting FLM 2 speed 3
48055 Number 0 100 Setting FLM 2 speed 2
48056 Number 0 100 Setting FLM 2 speed 1
48057 Number 0 100 Setting FLM 2 speed normal
48058 Number 0 100 Setting FLM 3 speed 4
48059 Number 0 100 Setting FLM 3 speed 3
48060 Number 0 100 Setting FLM 3 speed 2
48061 Number 0 100 Setting FLM 3 speed 1
48062 Number 0 100 Setting FLM 3 speed normal
48063 Number 0 100 Setting FLM 4 speed 4
48064 Number 0 100 Setting FLM 4 speed 3
48065 Number 0 100 Setting FLM 4 speed 2
48066 Number 0 100 Setting FLM 4 speed 1
48067 Number 0 100 Setting FLM 4 speed normal
48068 Switch 0 1 Setting FLM 4 accessory
48069 Switch 0 1 Setting FLM 3 accessory
48070 Switch 0 1 Setting FLM 2 accessory
48071 Switch 0 1 Setting FLM 1 accessory
48072 Number -32767 32767 Setting DM diff start add.
48073 Switch 0 1 Setting FLM cooling
48074 Number 50 400 Setting Set point for BT74
48087 Switch 0 1 Setting Pool 2 accessory
48088 Switch 0 1 Setting Pool 1 accessory
48089 Number 50 800 Setting Pool 2 start temp.
48090 Number 50 800 Setting Pool 1 start temp.
48091 Number 50 800 Setting Pool 2 stop temp.
48092 Number 50 800 Setting Pool 1 stop temp.
48093 Switch 0 1 Setting Pool 2 Activated
48094 Switch 0 1 Setting Pool 1 Activated
48133 Number 0 180 Setting Period Pool 2
48174 Number 5 30 Setting Min cooling supply temp S4
48175 Number 5 30 Setting Min cooling supply temp S3
48176 Number 5 30 Setting Min cooling supply temp S2
48177 Number 5 30 Setting Min cooling supply temp S1
48178 Number 5 30 Setting Cooling supply temp. at 20°C
48179 Number 5 30 Setting Cooling supply temp. at 20°C
48180 Number 5 30 Setting Cooling supply temp. at 20°C
48181 Number 5 30 Setting Cooling supply temp. at 20°C
48182 Number 5 30 Setting Cooling supply temp. at 40°C
48183 Number 5 30 Setting Cooling supply temp. at 40°C
48184 Number 5 30 Setting Cooling supply temp. at 40°C
48185 Number 5 30 Setting Cooling supply temp. at 40°C
48186 Switch 0 1 Setting Cooling use mix. valves
48187 Switch 0 1 Setting Cooling use mix. valves
48188 Switch 0 1 Setting Cooling use mix. valves
48189 Number 0 255 Setting Cooling use mix. valves
48190 Number 10 500 Setting Heatdump mix. valve delay
48191 Number 1 100 Setting Heatdump mix. valve amp.
48192 Number 10 500 Setting Cooldump mix. valve delay
48193 Number 1 100 Setting Cooldump mix. valve amp.
48194 Switch 0 1 Setting ACS accessory
48195 Switch 0 1 Setting ACS heat dump 24h-function
48196 Switch 0 1 Setting ACS run brinepump in wait mode
48197 Number 0 100 Setting ACS closingtime for cool dump
48226 Number 80 100 Setting Max charge pump reg speed
48282 Switch 0 1 Setting SG Ready heating
48283 Switch 0 1 Setting SG Ready cooling
48284 Switch 0 1 Setting SG Ready hot water
48285 Switch 0 1 Setting SG Ready pool
48452 Switch 0 1 Setting Auto heat medium pump speed, hw
48453 Switch 0 1 Setting Auto heat medium pump speed, heat
48454 Switch 0 1 Setting Auto heat medium pump speed, pool
48455 Switch 0 1 Setting Auto heat medium pump speed, cool
48456 Number 10 20 Setting Operational mode heat medium pump, cooling
48458 Number 50 100 Setting Max speed circ.pump Heat
48459 Number 0 100 Setting Speed brine pump cooling
48487 Number 1 100 Setting Speed circ.pump Cooling